Request for Proposals # 3675803
Overhaul of the Binns & Berry Trident L1000 lathe
| Current | "ChZPSN-Profnasteel" OAO | 31.05.2024 16:00 |
Request for Proposals # 3675795
Reducers according to technical specifications. Consider the equivalents.
| Current | "ChZPSN-Profnasteel" OAO | 29.05.2024 16:00 |
Request for Proposals # 3673727
... Expand
Performance of works on repair of a roof of plant management.
All materials and equipment for the execution of works are provided by the Contractor, except for the profile sheet and insulation.
1. Dismantling of the roof fence h-750 mm, with the preservation of materials - 60 m long;
2. Dismantling of the snegozadzhatel, with preservation of materials – 50 m long;
3. Dismantling of the existing steel corrugated roofing H75 on an area of 670 sq.m.;
4. Additional insulation of the attic floor with a semi-rigid mineral wadded slab (customer supply), h-100mm on an area of 600 sq. m
. 5. Installation of rafter protruding structures from channel 12 in the number of standard products 67 pieces and a total weight of 5.28 tons. (actual production drawings are issued by the customer after opening the roof);
6. Painting of m/structures;
7. Installation of a roof made of corrugated sheet H75 with replacement of the existing one by 50% (customer's delivery material);
8. Installation of the snow retention system;
9. Installation of roof fencing.
Warranty obligations: At least 60 months for completed works and materials.
Repair of the roof of the plant administration Samara, Krasnaya Glinka, 5th quarter, Electrical Panel-System Collapse
| Current | "ChZPSN-Profnasteel" OAO | 28.05.2024 12:00 |
Request for Proposals # 3669829
... Expand
Provision of maintenance services for Hitachi OSP55 M5ARN compressor.
Compressor room. Consists of three compressors:
Alup Largo 30-8 1pc
Alup Solo 30 1pc
Alup SCK42-8 2 pcs
Hitachi OSP55 M5ARN 1pc
As a result of inspection of the Hitachi OSP55 M5ARN compressor, the following was revealed:
1. Strong noise of electric motor bearings
2. The need for scheduled maintenance with replacement of oil separators.
3. Increased vibration and noise during compressor operation.
4. Destruction of the rubber damper of the compressor bed.
Provision of maintenance services for Hitachi OSP55 M5ARN compressor. Collapse
| Current | "ChZPSN-Profnasteel" OAO | 24.05.2024 06:00 |
Request for Proposals # 3667337
... Expand
1. Fan shaft:
• Drawing: TM 1918.00.000
• Quantity: 18 pcs.
• Material for manufacturing Steel 45
Shafts (Revolutions up to 3000 rpm) are used in the fan housing – the main part of the edge trimming unit on the mineral wool plate production line. With the help of this fan, crushed mineral wool products are transported, it has a large abrasive.
Fan shaft of the edge trim assembly Collapse
| Archived | "ChZPSN-Profnasteel" OAO | 23.05.2024 12:35 |
Request for Proposals # 3669412
... Expand
1. The KVO MVP-1 chain
• Material for manufacturing according to GOST 4543-2016,19281-2014;
• Quantity – 50m;
• Drawing: W6824APR;
It is used to transfer the mechanical power of mechanisms.
A reliable means of power transmission with high efficiency.
The assembled chain should have easy mobility of hinged
joints.
2. Lamellas KVO MVP-1
• Material for the manufacture of St3;
• Quantity – 130pcs;
• Drawing: MVP162-00.00;
The parts on the conveyor are subject to rapid wear due to the aggressive operating environment, these are temperature, friction, load. Therefore, a planned stop of the conveyor is envisaged to replace the components
with new ones
Cloaks of QUO, Chain of QUO Collapse
| Archived | "ChZPSN-Profnasteel" OAO | 23.05.2024 12:09 |
Request for Proposals # 3667331
... Expand
1. Shank 2-4 rolls:
• Material for manufacture: Steel 06H12NZD
• Drawing No.: CF-01.00.332;
• Quantity: 40 pcs.;
2. Shank of the 1st roll
• Material for manufacturing; Steel 06H12NZD
• Drawing No.: TM 2298.00.000;
• Quantity: 10 pcs.
3 . The Ring
• Material for manufacturing Steel 40X;
• Drawing No.: CF-01.00.310;
• Quantity: 16 pcs.
4. Graphite-fluoroplastic seal:
• Material for the manufacture of F4K20;
• Drawing No.: TM 1624.00.000;
• Quantity: 60 pcs
5. Support:
• Material for the manufacture of LS 59-1;
• Drawing No.: TM 01.00.201;
• Quantity: 40 pieces
Shank 2-4 rolls, Shank of the 1st roll, Graphite fluoroplastic seal, Ring, Support Collapse
| Archived | "ChZPSN-Profnasteel" OAO | 23.05.2024 12:00 |
Request for Proposals # 3667342
... Expand
1. Rear SKIP wheel:
• Drawing: RP 12219N.1-125SB
• Quantity: 2 pcs.
• Material for manufacturing Steel 3, paronite H1, Steel 45
2. The wheel on the SKIP front:
• Drawing: RP 12219N.1-115SB
• Quantity: 2 pcs.
• Material for manufacturing Steel 3,Steel 35,Sheet 18
SKIP wheel (rear,front) Collapse
| Archived | "ChZPSN-Profnasteel" OAO | 23.05.2024 12:00 |
Request for Proposals # 3665063
... Expand
Provision of services for pumping, transportation and cleaning of liquid household waste (LW).
1. The volume of the tank is 12 m3.
2. The number of tanks – 5 pcs.
3. The estimated number of bids for the export of concrete products per year: 5 pieces.
The customer has the right to change the number of services, in the direction of increase or decrease.
10. The bid is submitted on working days from 08:00 to 17:00 local time, with mandatory indication of the number of flights and the address of the facility by phone specified in the contract.
Provision of services for pumping, transportation and cleaning of liquid household waste. Collapse
| Archived | "ChZPSN-Profnasteel" OAO | 23.05.2024 10:00 |
Request for Proposals # 3669778
... Expand
Rendering of major repair services for the Renner RS 1-30 compressor.
Compressor room. Consists of three compressors:
Alup Largo 30-8 2pcs
Alup SCK-22 1pc
Renner RS1-30
As a result of inspection of the Renner RS 1-30 compressor, the following was revealed:
1. Strong noise of the bearings of the electric motor and the screw block.
2. The axial backlash of the rotor of the screw block is beyond the manufacturer's tolerance
3. Increased vibration when starting the compressor.
4. Destruction of the rubber damper of the compressor bed.
Rendering of major repair services for the Renner RS 1-30 compressor. Collapse
| Archived | "ChZPSN-Profnasteel" OAO | 23.05.2024 09:00 |
Request for Proposals # 3665010
... Expand
Partial technical inspection of lifting facilities in accordance with the requirements of Rostechnadzor Order No. 461 dated 11/26/2020 "On Approval of Federal Norms and Rules in the field of industrial safety Safety Rules for Hazardous Production facilities where lifting facilities are used."
It is necessary to carry out:
partial technical inspection of lifting facilities – 7 units:
- overhead electric double-girder crane controlled from the floor (head No. 27017, carrying capacity 10.0 tons);
- overhead electric double-girder crane controlled from the floor (head No. 27016, load capacity 10.0 tons);
- overhead electric double-girder crane controlled from the floor (head No. 27015, load capacity 10.0 tons);
- overhead electric double-girder crane controlled from the floor (head No. 27014, load capacity 10.0 tons);
- overhead electric double-girder crane controlled from the floor (head No. 27018, load capacity 10.0 tons);
- overhead electric single-girder crane controlled from the floor (head No. 7686, carrying capacity 3.5 tons);
- overhead electric single-girder crane controlled from the floor (head No. 8448, carrying capacity 3.5 tons).
Partial technical inspection of lifting facilities in accordance with the requirements of Rostechnadzor Order No. 461 dated 11/26/2020. Collapse
| Archived | "ChZPSN-Profnasteel" OAO | 23.05.2024 08:00 |
Request for Proposals # 3669753
... Expand
Provision of maintenance services
Compressor room. Consists of three compressors:
Airpol PR30 2 pcs
Airpol 30 1pc
As a result of inspection of the Airpol PR30 P19381213 compressor, the following was revealed:
1. Strong noise of electric motor bearings.
2. Increased vibration when starting the compressor.
Provision of maintenance services for the compressor Airpol PR30 P19381213. Collapse
| Archived | "ChZPSN-Profnasteel" OAO | 23.05.2024 08:00 |
Request for Proposals # 3664986
... Expand
Provision of services for commission psychiatric examinations.
1. Requirements for the Contractor.
1.1. Availability of a license to carry out activities.
1.2. Confirmation of freely available and owned (rented) equipment necessary for the provision of services.
1.3. The Contractor is fully responsible for the activities performed
1.4. The Contractor is responsible for the high-quality and timely performance of services for conducting preliminary (when applying for a job) and periodic medical examinations in accordance with the requirements of Russian legislation
2. Place of work:
At the location of the medical organization in Samara.
Provision of services for commission psychiatric examinations. Collapse
| Archived | "ChZPSN-Profnasteel" OAO | 22.05.2024 08:00 |
Request for Proposals # 3664968
... Expand
Provision of services for conducting preliminary (when applying for a job) and periodic medical examinations.
Requirements for the Contractor.
1. Availability of a license to carry out activities.
2. Confirmation of the freely available and owned (rented) equipment necessary for the provision of services.
5. The Contractor is fully responsible for the activities performed
6. The contractor is responsible for the high-quality and timely performance of services for conducting preliminary (when applying for a job) and periodic medical examinations in accordance with the requirements of Russian legislation.
7. The driver of the vehicle and accompanying persons (if necessary) must have with them an identity document (passport), a driver's license, and a vehicle registration certificate.
2. Place of work:
Preliminary medical examinations – at the location of the medical organization.
Periodic medical examinations:
- Krasnaya Glinka, Krasnoglinskoe highway 20 - p.
Volzhsky, Krasnoyarsk district, Production 1
- Alekseevka settlement, Zavodskoy proezd 1
- Samara, Zavodskaya str., 5
Provision of services for conducting preliminary (when applying for a job) and periodic medical examinations. Collapse
| Archived | "ChZPSN-Profnasteel" OAO | 22.05.2024 06:00 |
Request for Proposals # 3664427
... Expand
Manufacture of spline shafts for carriage travel of overhead electric cranes.
1. To make spline shafts from 40X steel grade according to the drawing
2. Perform heat treatment of the spline 47-52 HRC according to the technical documentation.
Manufacture of spline shafts for carriage running of overhead electric cranes. Collapse
| Archived | "ChZPSN-Profnasteel" OAO | 21.05.2024 12:00 |
Request for Proposals # 3664403
Purchase of LED lamps
1. LED lamp SPO-107D 36W 160-260V 6500K 2900Lm 1200mm with motion sensor IP40 ASD - 2 pcs.
2. LED lamp 595*595mm Armstrong ceiling with light sensor and motion sensor - 49 pcs.
| Archived | "ChZPSN-Profnasteel" OAO | 20.05.2024 16:00 |
Request for Proposals # 3653115
... Expand
1. Drive shaft No.2:
• Drawing: TM1499.00.000
• Quantity: 2 pcs.
• Material for the manufacture of ST3SP, Stal20, STALB10
2. Drive shaft:
• Drawing: TM 1458.00.000
• Quantity: 2 pcs.
• Material for the manufacture of ST3SP, Stal20, STALB10
3. Driven shaft:
• Drawing: TM1658.00.000
• Quantity: 2 pcs.
• Material for the manufacture of ST3SP, Stal20, STALB10
4. Roll on the pendulum clamshell (front):
• Drawing: TS350.02.000
• Quantity: 2 pcs.
• Material for manufacturing Steel 35
5. Roll on the pendulum clamshell lower rear
• Drawing: TS350.01.100
• Quantity: 2 pcs.
• Material for manufacturing Steel 35
6. The roll on the pendulum folding inclined rear
• Drawing: TS350.01.000
• Quantity: 2 pcs.
• Material for manufacturing Steel 35
7. The upper roll on the pendulum clamshell
• Drawing: MVP 120.02.000
• Quantity: 2 pcs.
• Material for manufacturing Steel 35
Shafts for the MVP-1 and MVP-2 pendulum clamshell Collapse
| Archived | "ChZPSN-Profnasteel" OAO | 17.05.2024 15:11 |
Request for Proposals # 3657719
Provision of audit services for annual accounting (financial) statements
| Archived | "ChZPSN-Profnasteel" OAO | 17.05.2024 14:00 |
Request for Proposals # 3653110
... Expand
1. Separator:
• Material for making Circle 270/ Circle 45;
• Drawing No.: TM 1838.00.000;
• Quantity: 36 pcs.;
• Angular displacement rel. M60*2 is not more than ± 10` (according to the drawing);
• Circle 270 GOST 1133-72;
• Circle 45 GOST 1050-88;
2. Blower of the 3rd roll of the centrifuge MVP2 (gap 16mm):
• Material for manufacturing Steel 20;
• Drawing No.: TM 2014.00.000;
• Quantity: 36 pcs.
3 . Blower of the 4th roll of the centrifuge MVP2 (gap 16mm):
• Material for manufacturing Steel 20;
• Drawing No.: TM 2015.00.000;
• Quantity: 24 pcs.
4. Pulley on the electric motor:
• Material for manufacturing Steel 45;
• Drawing No.: TC 331.00.001A;
• Quantity: 36 pcs
Separator, blower of the 3rd and 4th rolls, pulley for electric motor Collapse
| Archived | "ChZPSN-Profnasteel" OAO | 17.05.2024 12:10 |
Request for Proposals # 3661686
... Expand
Repair of the exhaust ventilation duct - Exhaust chamber (VS-7).
Scope of work:
1. Dismantling of existing ducts with a total area of 35.9 m2;
2. Expansion of openings in the wall for the passage of air ducts;
3. Supply and installation of air ducts 1500*1500mm of galvanized steel
1.5mm and transition 1500*1500/1150*1150 with a total area of 47.4 m2;
4. Manufacture and installation of supports for air ducts;
5. The maximum height of the work performed is 4 m. All materials and mechanisms are provided by the Contractor.
Warranty:
The warranty period for the repair work performed must be at least 1 (one) year
Repair of the exhaust ventilation duct. Collapse
| Archived | "ChZPSN-Profnasteel" OAO | 16.05.2024 06:00 |